Commented on a post

Sorry for the delay. Working on getting the information. Our guy that does that has been out. We have a large tumbler, so we can do multiple heads at one time. Will get back to on the type of media...

18 hours ago 2
Posted an answer
Hand picking a KE4 Tour TC rdrver for loft?

In the Neutral position (or any position for that matter) I am confident there would not be a degree variance in the TC Driver.  Would be very time consuming and thus add some cost for us to go through...

18 hours ago 5
Posted an answer
Jim or Britt, what kind of clear coat and paint do you use when you refinish a metal wood?

Generally we use PPG Automotive paints for metal woods.  Also use compatible clearcoats.  The clear coat mix is 4 parts JC620 Urethane with 1 part JH6285 Hardener, with about a bottle cap full of thinner...

18 hours ago 5
Answer was selected as best
2 days ago 10
Posted an answer
Moment X Putter – TSW Wedges – MaxFli Tour X

Good Statement.  Like to hear about those kind of results. Thanks for sharing. Britt Lindsey

2 days ago 5
Posted an answer
Backorder In-Stock Update

We have them on order.  The lead time has been a real challenge on the tools we import, of which the MA2012 is one.  We are trying to get an update on the status.  Currently we are being told January,...

3 days ago 5
Posted an answer
Ping Eye 2 refinishing

When we do Ping, we would first use a 220 grit belt to clean up any nicks, etc., then we put them in our big tumbler.  The rock media we use basically restores the original finish, or very similar. ...

3 days ago 5
Posted an answer
Single length golf clubs

Rlafoone is correct.  If you are doing 1 length clubs and want to do them so that they are playable, all the head weights must be the same and you would trim a single blank shaft (from the tip for flex)...

3 days ago 5
Posted an answer
Tip Size Callaway Apex 19 irons

Apex 19 are .370.  Apex Pro would be .355.  So if they are just the Apex 19, the hosels ID is .370. Britt Lindsey

3 days ago 5
Answer was selected as best
4 days ago 10
Posted an answer
recommended wedge length , when your irons are – 1/2

There are several options that are acceptable.  Really comes down to what you prefer.  I have seen the PW, GW, SW and LW all the same length for some, especially when the clubs are shorter than standard. ...

4 days ago 5
Commented on a post

You can put the 9 iron shaft in the 8 iron head. The Nippon 950 GH #9 iron shaft is 35.5" to start with. If you install and assume 1" bottom of the bore to heel dimension (could be 1.25"), then your...

5 days ago 2
Posted an answer
KE4 Max lineup?

There is a KE4 Max iron set in the works.  Already being tooled as we speak.  It will be an Ultra Game Improvement design with one weight port for head weight adjustability.  We are hoping to have metal...

5 days ago 5
Posted an answer
New M Series Wedges

Specs will be basically the same, from a loft and bounce standpoint, as the M-Series Plus wedges.  We will only carry the 0.90" sole width option and the 1.05" sole width option. 0.90" sole width will...

5 days ago 5
Commented on a post

Whoever assembled it could have installed with a brass or copper tip weight for swing weight purposes. You could try heating slightly and may be able to pull out with some needle nose pliers. Or, you...

September 17, 2021 2
Posted an answer
Mizuno ST190 fairway wood re-shaft

Not sure what you are referring to on the "centering plug" part of the question.  Sometimes when you remove a shaft that had a tip weight the weight can be stuck in the hosel.  That could be mistaken...

September 17, 2021 5
Posted an answer
Are these shafts reusable

Most likely they were .335" tip diameter and I don't know how long the tip parallel length was.  Whether or not you can use them on an iron depends on the tip diameter, but even if the shaft is larger...

September 17, 2021 5
Posted an answer
Trimming discreet length iron shafts

The parallel tip section length is only abut 2.5", so you really can't trim any additional.  Possibly 1/2", but the discrete lengths on the Nippon are a little shorter so if you trim the 1/2 inch from...

September 16, 2021 5
Posted an answer
New M Series Wedges

Here is one of the Max 1.05 with the 2 screws.

September 15, 2021 5
Posted an answer
New M Series Wedges

Below is the Max 0.90 (0.90 denotes the sole width) ack and face. It will come in a 50, 52, 54, 56 and have the 3 weight screws.  There will also be the Max 1.05 that will have lofts of 54,56,58,60 and...

September 15, 2021 5
Load More