Answer was selected as best
January 27, 2021 10
Posted an answer
CPM charts for Woods and Irons

If you look at the frequency chart at this link,  https://www.golfworks.com/iron-frequency-chart-examples/a/1656/  this was information we used to create especially the iron chart.  It helped us create...

January 26, 2021 5
Posted an answer
Replacement King Cobra Autoclave shaft

The King Cobra Autoclave senior flex shaft actually weighted 97 grams.  It was designed to create a high trajectory.  The first shaft that comes to mind would be the Grafalloy ProLaunch Blue A flex iron...

January 21, 2021 5
Posted an answer
Is a callaway epic pro 1997 model bendable?

I spoke with Callaway and they tell me you should be able to adjust these up to 2 degrees for both loft and lie.

January 13, 2021 5
Posted an answer
How to make my club longer?

You can use a graphite shaft extension like the GW4000.  https://www.golfworks.com/premium-graphite-shaft-extensions/p/gw4000/  You will need to measure the inside diameter of the shaft at the butt end...

January 8, 2021 5
Posted an answer
Adjusting Loft Angle

With either the KE4 of STi irons we do not recommend adjusting them more than 2 degrees.  2 degrees is the maximum we will adjust them here at GolfWorks.  The 5 iron would be assembled at 1/2" longer...

January 8, 2021 5
Posted an answer
Utility irons vs. SGI irons

We have never done any of our MPF testing on the Utility irons to know for sure how the measurement of CG and MOI compare to an iron like the T400.  The T400 iron tests as a very forgiving iron.  Even...

January 7, 2021 5
Posted an answer
OEM Driver bore depth resource.

I am not aware of anyone that might have this information.  Here at GolfWorks for all the shaft preps that we do for customers we sand 1".

January 7, 2021 5
Posted an answer
Bore thru removal

There really is no difference in removing a shaft from a bore through wood then there is with a non bore through.  The process is the same.  I always use a heat gun on a high setting and heat the back...

January 7, 2021 5
Commented on a post

Tipping the Pro Series DR R flex would actually make it stiffer than the IZ 60 S. It was very close as it is.

January 6, 2021 2
Posted an answer
Cobra Baffler TWS 5 Hybrid

2" would be your tip trim for this Cobra TWS 5 hybrid.  The Dhi wood shaft only has a 3.5" parallel tip section and you need to leave 1.5" for proper installation so 2" is the max you can tip trim.

January 6, 2021 5
Posted an answer
Bestseller: The Golf Club Identfication and price Guide

As I mentioned in the email you sent to me you would have to have your friend in NY purchase the book for you and ship it to you.  We are unable to sell to Austria.  The PGA Value Guide is online only.

January 6, 2021 5
Answer was selected as best
January 6, 2021 10
Answer was selected as best
Rebore to .370

The reason I put to rebore them was at that time there were no go options in a .355" taper tip shaft to use as a replacement.  These days we have a couple of options plus we can special order any UST...

January 5, 2021 10
Posted an answer
Ke4 tour driver finally getting one but shaft question

When I go through the shaft profile data for the Graphite Design Tour AD IZ 60 S flex and compare it to the profile data for the shafts we offer in the Club Pak for the KE4 Tour TC driver the closest match...

January 5, 2021 5
Posted an answer
Which wedge for tight lies in the fairway?

I would go along with using more bounce or a wider sole.  Wider soles play like they have more bounce.  Also make sure when you hit these shots to use the bounce angle and do not try to hit the shots...

January 5, 2021 5
Posted an answer
Maltby KE4 drove tungsten weights

It is hard to say for sure if changing the weight will change your spin numbers or how much effect it would have on the spin.  Decreasing the weight will make the shaft slightly stiffer and that could...

January 5, 2021 5
Posted an answer
Old school shaft

The original Rifle 6.5 shaft weighted 130 grams and was a mid/high bend point and firm tip.  It was designed to create a low/mid trajectory.  To match those playing characteristics in graphite shafts...

January 5, 2021 5
Posted an answer
maltby m-series forged wedges

In the M-Series+ (MA0257) wedges we have the Tour, Mid and Wide.  At this link if you scroll down the page you will see all the specifications listed with the bounce angles and in the Overview we read...

January 5, 2021 5
Posted an answer
Shaft , head adapter for Cleveland driver head

To be able to answer your questions I need to know which model Cleveland driver you have?

January 5, 2021 5
Load More