Michael...just saw this. Thank you for the reply! I have a TS3 6i with KBS PGI 80 coming. Can't wait to give it a try! I chose that shaft in particular because it has a little friendlier profile than...
I prefer the consistent weights of .355 iron shafts, but I see very few available in the Custom Shop. Curious why that might be, and whether or not I can still get Custom Shop benefits if I were to go...
Given my SS, would you suggest the S-flex, R-flex, or possibly a soft-stepped S? Also, same question for the Maltby shafts...I'm not opposed to trying one? Thank you again, and for goodness sake, I'll...
Thank you for your feedback. My driver SS is still between 95-100, with my average carry being 230ish. My average 6iron SS is 78-80, with average carry 165ish. My recent fitting at Club Champion confirmed...
Yes, thank you Shawnblue. I did get the original correspondence about minimal cg shift...
More comments/questions. The iron shafts I'm obsessing about are the Aerotech CW80's. I like the lower torque rating, as it implies they might be a little more consistent. I read somewhere they have...
Quality reply, Britt...thank you! The clubs I'm struggling to launch have the same lofts as my previous set, but the characteristics are different. I had P790's, and moved to JPX 925 Forged. It was...
As as aging competitive senior player, my questions about iron fitting surround iron lofts. I noticed a fairly significant decline in my distances this past year, especially in my 5, 6, 7 irons...the...
Thank you. If I was to go through the custom club section, would Golfworks be able to assemble to my D0 request? Are there disadvantages to adding so much weight in the tip?
Hello, All. Here for your expert wisdom again. I'm greatly interested in a set of Maltby TS3 with KBS TGI 80 shafts. Without making them "over standard" length, I'm wondering if swingweights in D0-D2...
Is it true that the numbers don’t lie from a Trackman-based club fitting? Even if it is conducted indoors on mats? I’ve been notoriously bad hitting off mats. I always perform better off of real...
Just to follow up. I went to club champion and got a formal iron fitting. The shaft that I’m going to retrofit is the Nippon Pro Modus 120 S flex. It gave me 700 RPM more spin. Nine more yards of carry...
Thanks to everyone! Britt, I AM somewhat kicking myself for not just staying with the DG 105's. Rather than this become an an expensive overhaul right off the bat, I'm probably just going to reshaft...
Curious, does anyone know what the FCM would be in a soft-stepped C-Taper lite? I know sub-flex is less talked about these days, but wondering if someone knows. I found a Wrx post from 2012 that said...
I respectfully disagree with your premise as applied to this situation. I do accept the lighter weight premise, and have considered graphite. In fact, I played Yonex ADX Tours while in my prime with graphite...
I recently purchased as set of JPX925 Forged irons (5-GW) with S-flex KBS C-Taper Lite shafts. Just getting used to them, and there is a lot to like, except they distance/yardages I get are quite a bit...
Wondering if Maltby had a hand in the design of the new Maxfli irons? The one model looks suspiciously like the TS3's...
Saw mention of TS 3.5 in another thread, but couldn’t find any info on it. What are the design differences between it and the TS3? Also, what is the estimated rollout date? Thanks in advance.
Wondering if there will be any MPF updates coming soon? Hopeful to see MPF's of the releases from last summer/fall and the additional ones released more recently...
Curious...what are the differences in design characteristics between the TS3 and the TS3.5?