I made a post last week about being in my off-season and experimenting with PX LZ shafts with my irons (from DG 120 S300) and what to do with wedge shafts. My irons are the (amazing) Maltby TS3's which...
The Ping i240 have a 431 MPF, 15.8 MOI, .870 Actual VCOG. LINK: https://store-k9nvqai7wz.mybigcommerce.com/content/PDFs/Head_MPFs/MPF_PING.pdf
I've entered my tournament off-season and I'm experimenting with some LZ 6.5's in my irons. Was using DG 120's in Stiff and I had issues with ballooning at my swing speed (115+ driver). The X-Stiff in...
It looks like the 2022 Callaway UW uses .335 shafts. But they're cut to roughly hybrid length (17* and 19* are 41.5"). I'm concerned about swingweight and performance. Would I tip trim the shaft to whatever...
Had someone looking for a reshaft and they asked me about their old Pings and I wanted to "check my math". My guess as a modern available replacement would be the DG Mid 115 X100 or S300 hard stepped....
Basically what you listed is close, but in Ralph's original book on Design, Fitting and Repair he listed 43" as the standard driver length for a driver, 42" for the #3 wood, 41" for a #5 wood and 40" for...
I believe the newer standard length chart from Golfworks has removed the steel specs for woods. I can't find my old ones. Can you confirm if it's basically: 1/driver- 43.5" 3W- 42.5" 5W- 41.5" 7W-40.5"...
I feel like I've seen this discussed before but couldn't find where. But I have come across a few Pings with X100U shafts. I doubt Ping is reaming their hands at the factory. Are they crimping those .370...
Got a link? I have looked on Amazon and only see solvent activated. No water activated that I can find.
So, has this stuff been banned or was there just like 1 manufacturer in China making it and they're gone? I can't find the water activate tape any where and I think I saw a question answered by Jim before...
I have had a Rapport Core Blue FW 70TS installed in a 3 wood for about a year. It seemed to develop a creaking sound last night at the range. I had this happen on a HZRDUS Smoke Blue 6.5 60 a couple years...
Kind of ironic that his name was brought up. Mr. Miura passed away yesterday at 82. https://golf.com/gear/irons/katsuhiro-miura-founder-of-miura-golf-dies/
Something I've always been fascinated with is golf club design and philosophy. Why did this person do something a certain way. I was wondering if there was any books or anything that went over this and...
Moving some shafts around. Was going to put some UST Recoil 95 .355 in my old Ping i15 set but the raw tip extends beyond the hosel. The i15s seem to be the last iron they did that did not use ferrules....
If I add a heavier weight to the KE4 Tour+ irons, what effect would it have? I normally play at D3 in TS3's but I'm moving from DG 120 S300 down to some graphite shafts for low back and fatigue issues....
Britt, you have a #5 FDI? That exists? Prototype?
Britt, Do you have a bottom of bore to ground measurement for the KE4 Tour+ and TS3? I have some shafts I may want to change over and didn't know if I'd need to mess with extensions and regripping. Also,...
May have been an iron head whacking it while in the bag/on the cart. I get super paranoid about irons moving into the covers over my woods. I like the covers with "socks" for that reason.
I saw back in October that there may be some Pure Track putters in the pipeline coming in the future. Whether that's 2025 or not was not said. I really liked the weight and feel of the PTM-1 and PTM-5...
Is the balance point of a UST Recoil 95 or 110 in .355 lower than most graphite shafts? I was messing with some per the post I made a few weeks ago discussing swingweight for these and the ProLaunch Red...