Commented on a post

I have had an Icon and a PTM side by side and the difference is drastic. Hosel length and C dimension alone are gonna throw the Icon WAY down the list. The Icon doesn't stray too far from the original...

June 6, 2021 2
Posted an answer
Jim, (or anyone with actual facts), are more expensive shafts really made any different?

A novel could be written on this. Some materials in shaft construction are cerrainly higher in cost than other. Method of construction also plays a part. Flag rolled or filament wound. There are different...

May 26, 2021 5
Asked a question
TSW DRM 52 is a wow

I put a 52° DRM wedge in play today and had a true oh wow moment. When the chrome version.came out I grabbed the 52 and the 56. I couldn\'t get settled in with the feel and quickly went back to my M Series...

May 22, 2021 2
Commented on a post

If you were going to stay lock step with the lofts the H4 and H5 would fit perfectly. Some players can get much better performance with a hybrid. Easier to hit, higher launching, they might go quite a...

April 13, 2021 2
Commented on a post

The dremel would have only been used to lightly score the inside of the adapter.... But!! I received a batch of adapters yesterday..it appears there has been a CHANGE in the adapters. There are now CUT...

April 5, 2021 2
Asked a question
KE4 TC adapters

Am I the only one who can't seem to get these adapters to bond to a shaft. I'm probably at a 25% success rate. I scuff up the adapter with a wire brush. Properly prep the shaft tip and am using new or...

April 4, 2021 2
Posted an answer
Shaft tipping

A half inch should work for the 7 wood.

March 6, 2021 5
Posted an answer
Iron design for higher spin

@Therty I spend a ton of time on a simulator and seeing the effects of a high VCOG iron in real time is tough to notice. What I have seen in real-time is where contact is made and it's huge effect on spin. ...

February 17, 2021 5
Posted an answer
TS-2 general feel of club head

Of the designs currently available the TS-2 has the best 'overall' feel of any clubhead in the catalog. The TE and the TS-1 when hit pure are as good as any forged iron from any source in the feel department,...

February 15, 2021 5
Posted an answer
Driver comparison

A lot of information is missing from your question to give you a true recommendation... But.. as a high handicapper you more than likely first off need more loft in your driver. So right there the KE4...

January 20, 2021 5
Asked a question
OEM Driver bore depth resource.

I have been doing a ton of shaft builds for online customers and the OEM heads are all over the map. Is there a guide or a resource that lists the bore depth so I can easily make up shafts with out having...

January 6, 2021 2
Asked a question
M-SERIES + replacement

Please tell me that you have plans for replacement for this amazing line of wedge heads. I had just seen the website stating that a lot of the models are no long available. The versatility and ease of...

January 1, 2021 2
Commented on a post

I don't know your game or your swing fault that's causing you to lose confidence and get the yips. What I do know is the wedge designs with the wider soles will allow you to gain a lot of confidence that...

January 1, 2021 2
Posted an answer
TS1 TS2 Combo?

I have played that combo earlier in the year and it's a fairly natural blend. I found the gaps as stated by factory specs to be very manageable. If you get on a launch monitor or out in play and are seeing...

December 30, 2020 5
Posted an answer
Head comparison TS1 / STi2

The STI2 is not a hollow iron. It's undercut and some of the long irons have a gel in the cavity. The two irons are quite different. The wider sole of the STi2 allows them to really prevent digging. The...

December 26, 2020 5
Posted an answer
What is the process to determine if hard or soft stepping shafts is necessary?

As for what data do you look at for fine tuning a shaft? For me its trial and error. Not really a set data point. What is actually working for that golfer. What are they trying to correct. What does the...

December 7, 2020 5
Asked a question
PTM chrome,

I was surprised to see the PTM chrome are back in stock. Did these get a reprieve from the chopping block? How long can I expect these to be in the portfolio as they have been my best selling Maltby head.

December 7, 2020 2
Commented on a post

Thank you for the response. In the recent influx of shafts I have been working with I am seeking a +/- 3 cpm factory tolerance and the upper vs lower range really show a difference. So an S flex shaft...

November 24, 2020 2
Asked a question
CPM reduction by softstepping

Aside from building clubs and actually measuring the reduction in CPM is there a general rule of thumb on the CPM reduction when softstepping?

November 20, 2020 2
Commented on a post

Given a blank sheet of paper this is almost exactly what my dream setup would be. Breaking up the clubs into three groups. Scoring clubs, mid irons and long irons. Going from a near muscle design to a...

October 27, 2020 2
Load More