Asked a question
Gollf clubs for women

I want to build a golf club for my wife and need some advice as where to begin. She has a consistent swing and 60-70mph club head speed with driver 140-150yds on a average drive. Not over powering as she...

June 25, 2022 2
Asked a question
Beginner clubs for 10 yr old grils and 14 year old boy

What would be a recommendation for golf clubs for a 10 year old gril and 14 year old boy. They are jest starting to hit clubs on my simulator and would like to build a small set to help them learn the...

May 25, 2022 2
Commented on a post

Thanks gives me a lot to think about.

April 12, 2022 2
Asked a question
Graphite shaft cost

What makes a $100.00+ golf shaft better than a $25.00+ golf shaft? For a 12-14 handicap would it make a difference in the higher end of golf shafts. I have started to experiment with building golf clubs...

April 11, 2022 2
Commented on a post

I ended up with the m890 launch tech witch I understand is for woods and not hybrid. I have been in contact with customer service and very helpful. Thanks

April 6, 2022 2
Asked a question
5 hybrid shaft

I purchased the Maltby 5 hybrid and the m890 shaft and came to find the shaft is a .335 and nosel .370. What would be the recommendation for a shaft with .370 tip.

April 5, 2022 2
Commented on a post

Thanks for all the help on recommendations as I am in a learning curve wanting to learn more about club heads,shafts etc.

March 19, 2022 2
Asked a question
Replacement for a 6 iron

I currently have the ts-2 6 iron with the ust iron hl r flex and find that I not being consistent when playing. I am thinking of changing to a hybrid  that would be between my tm burner 5-24* rescue,...

March 18, 2022 2
Commented on a post

My mistake as miss read the chart on ustmamiya web site. Thanks for the correction

March 14, 2022 2
Asked a question
Tip trimming

I have the PROFORCE V2 HL 6F3 that has the tip trimmed 2" and want to use for my 5 wood, trim specs call for 3" end trim for the 5 wood. What could I except with the 2" tip triming?

March 14, 2022 2
Commented on a post

Thanks Rlafoone as it was the pured shaft mentioned pervious. .

February 27, 2022 2
Asked a question
Driver shaft mistake

I have the proforce v2 6f3 hl pured shaft that I install the adapter on for my tm m1 driver. I didn't align it correctly and tried to remove with heat and didn't have and extractor. I applied to much heat...

February 26, 2022 2
Commented on a post

Thanks for the explanation on the differance of the two heads. Is the 2 piece forged head a better head?

February 24, 2022 2
Asked a question
Iron heads

Why is Maltby KE4 Tour + Iron Heads vs TS-2 such a difference in the cost between the 2?

February 23, 2022 2
Asked a question
TM adapter installation on pured shaft

just received my new pured golf shaft with a TM adapter and I am not sure how to align the pure line to the dapter.

February 18, 2022 2
Asked a question
Swing weight

I wanting to learn about swing weight and adapt my clubs according to my golf swing. How would I determine my swing weight?

February 8, 2022 2
Commented on a post

Added to my question is my tempo according to garmin s60 is 2.5- 2.7, my path most of the time is more out to in and pushes the ball with some right to left spon. I also can push the the ball straight...

January 10, 2022 2
Asked a question
Ts-2 6 iron

I am contemplating purchasing the ts-2 6 iron and would like recommendation on shaft to use. I currently have tm4 irons with stock shaft. I currently hit the tm 6 iron 150yds. I am looking to be able to...

January 8, 2022 2
Asked a question
Driver shaft

I recently ask on useing this shaft to replace my taylormade m2 stock shaft. The proforce v2 R 63 weight  I currently have this shaft on my 3 sims 3 wood and when I hit it well it will go 220yds. Do I...

December 17, 2021 2
Asked a question
Driver shaft

I currently have the UST Mamiya Proforce V2 HL Graphite Wood Shafts on my sims 3 wood and off the tee I can hit it 220yds which is further than my M2 taylormade driver with stock shaft.. I am thinking...

December 14, 2021 2
Load More