I came from MG's and went to Cleveland RTX Zipcore (version 5). I've been playing the DRT in 50-G, 56-A, and 60-A. The 50 works well. But I have some issues getting that tight zippy spin on the 56 and...
I checked on this last year in July. Basically the chemical used for the product were diverted to other industries and became unavailable. Golfworks had been working to find a substitute but nothing had...
I just wanted to pass along my condolences with Ralph Maltby's passing. I apologize for this being so late but I just found out. I'm not sure of all of the relationships he maintained at Golfworks and...
So, I used to putt by feel quite a bit and for a long time, I used a Yes! Tracy II (flow neck) with only a topline dot. I would drop some mid-range and long putts but struggled with shorter range. Just...
Would the KE4 Forged or STI (Gen 2) be a replacement for the older Tour+? Seems like both have similar features, specs, and lines, with the Forged offering only interchangeable weight. With lighter head...
I was curious how the M980's were coming along and how they would compare to the KE4 MAX irons, especially for a slower swing speed female beginner. MPF looks similar. Also if you have any pics since she's...
What are the recommended or typical weights for ladies' clubs? Do head weights differ? I would imagine they would be C0-C4, with the shorter length alone. Take, for example, the KE4 MAX irons. The 8 iron...
I play TS3's in 4-6 irons and I need to bridge a gap down to my 17* club. I'm thinking about swapping the 4-5 TS3's for TS3.5's and would gain yards due to the lofts. But I see that CMC and polymer is...
I made a post last week about being in my off-season and experimenting with PX LZ shafts with my irons (from DG 120 S300) and what to do with wedge shafts. My irons are the (amazing) Maltby TS3's which...
The Ping i240 have a 431 MPF, 15.8 MOI, .870 Actual VCOG. LINK: https://store-k9nvqai7wz.mybigcommerce.com/content/PDFs/Head_MPFs/MPF_PING.pdf
I've entered my tournament off-season and I'm experimenting with some LZ 6.5's in my irons. Was using DG 120's in Stiff and I had issues with ballooning at my swing speed (115+ driver). The X-Stiff in...
It looks like the 2022 Callaway UW uses .335 shafts. But they're cut to roughly hybrid length (17* and 19* are 41.5"). I'm concerned about swingweight and performance. Would I tip trim the shaft to whatever...
Had someone looking for a reshaft and they asked me about their old Pings and I wanted to "check my math". My guess as a modern available replacement would be the DG Mid 115 X100 or S300 hard stepped....
Basically what you listed is close, but in Ralph's original book on Design, Fitting and Repair he listed 43" as the standard driver length for a driver, 42" for the #3 wood, 41" for a #5 wood and 40" for...
I believe the newer standard length chart from Golfworks has removed the steel specs for woods. I can't find my old ones. Can you confirm if it's basically: 1/driver- 43.5" 3W- 42.5" 5W- 41.5" 7W-40.5"...
I feel like I've seen this discussed before but couldn't find where. But I have come across a few Pings with X100U shafts. I doubt Ping is reaming their hands at the factory. Are they crimping those .370...
Got a link? I have looked on Amazon and only see solvent activated. No water activated that I can find.
So, has this stuff been banned or was there just like 1 manufacturer in China making it and they're gone? I can't find the water activate tape any where and I think I saw a question answered by Jim before...
I have had a Rapport Core Blue FW 70TS installed in a 3 wood for about a year. It seemed to develop a creaking sound last night at the range. I had this happen on a HZRDUS Smoke Blue 6.5 60 a couple years...
Kind of ironic that his name was brought up. Mr. Miura passed away yesterday at 82. https://golf.com/gear/irons/katsuhiro-miura-founder-of-miura-golf-dies/