Clubmaking Forum

discuss, ask and learn about golf and clubmaking

Commented on a post

Thanks Britt. I wanted to reuse it since I didn't want to throw off the swing weight and didn't have any on hand. I have some lead tip weights but I don't like that the head extends the shaft by approx...

May 10, 2024 2
Asked a question
Brass Tip Weight Removal

Hello, Yesterday I replaced a shaft in a Titleist T150 iron head.  After removing the shaft, a brass weight stayed in the head.  I applied heat to the head and picked at the brass tip for probably 30...

May 10, 2024 2
Asked a question
T100 Ferrule

Hello, Anyone know the correct Titleist T100 iron ferrule SKU?  Will the Golfworks AP1 / AP2 ferrule work?  Thanks in advance.

April 30, 2024 2
Commented on a post

Sorry, I should have been more specific. Not available on the Canada website. I tried calling customer support and finally got thru. They confirmed RH is on backorder.

June 16, 2023 2
Asked a question
G425 Adapter

I am a right handed golfer.  The Ping adapter PGC005 is only available as LH.  If I leave the adapter setting on standard, can I use the LH? Thanks

June 16, 2023 2
Asked a question
Tensei Blue loose impediment

Hi, Last year I installed an after market Tensei Blue AV Series (SFW) on my G425.  Because I cut it 1 inch shorter than standard, I installed a tip weight to bring the swing weight to D4.  Saturday I...

May 22, 2023 2
Posted an answer
Changing steel shafts in irons to graphite shafts

From my own experience of installing graphite shafts a few years ago, my clubs ended up 4 - 5 swing weights lighter as Britt describes above.  I invested in a swing weight scale and added 10 gram lead...

April 28, 2023 5
Commented on a post

Thanks Britt. The Canada site only has the Premium extensions so I'll try the 0.575 (silver).

March 14, 2023 2
Asked a question
KBS MAX 80 Steel extension

Does anyone have the correct inside diameter for the KBS MAX 80 Steel shaft?  I need to order a few extensions for a friend and don't have the club in front of me.  I am guessing it requires a .575 extension...

March 14, 2023 2
Commented on a post

Thanks. I double checked the hosel depth again with a drill bit slightly smaller than .355 and it measured 1". All 3 heads measured the same so it appears accurate. I did not apply the epoxy during...

March 1, 2022 2
Asked a question
JPX900 Hosel Depth

Hi Just replaced a friends Mizuno JPX900 hot metal iron shafts with recoil .355 taper tip graphite shafts a few weeks ago. Used Golf Works Tour epoxy. Since then 3 shafts came off.  What concerns me...

March 1, 2022 2
Commented on a post

Thank You for all your feedback!

February 7, 2022 2
Commented on a post

Thanks for your advice. When I install the head very little epoxy escapes from the top. Probably because the club head is a very snug fit to the point where I need to apply a reasonable amount of force...

February 7, 2022 2
Asked a question
Head Installation Head

Hi Guys I added a tip weight to my graphite iron shafts and after applying the epoxy, the head does not remain snug against the ferrule. I am guessing because the tip weight head seals the small hole...

February 7, 2022 2
Commented on a post

Thank You. You advice is greatly appreciated.

January 20, 2022 2
Asked a question
Lead Tip Weights

If I install a Lead Graphite Shaft Tip Weight part GW01076 will this increase the shaft tip length by 1/4 inch and will this make the shaft tip play softer or is the change minimal?  Do I need to trim...

January 18, 2022 2
Registered
January 18, 2022 10