Clubmaking Forum

discuss, ask and learn about golf and clubmaking

Commented on a post

Good luck @Britt getting a 'Maxfli' iron in her hands

February 5, 2024 2
Commented on a post

In the GolfWRX thread I have some pictures of a removed badge. It's not overly flattering plus there is the hole for were the goo goes. So the badge needs to stay. Take some Acetone and some steel wool....

January 3, 2024 2
Commented on a post

I may have misconstrued my results with the KE4 Max. It suits my game amazingly well. I love everything about them. I've been gaming the PTM Blacks on and off for years. Recently I bought another set of...

November 15, 2023 2
Asked a question
DBM with higher VCOG

What are the chances of another PTM Black production run... OR a DBM KE4 Max. A DBM Max with adjustable weights would be amazing. Would fix my only complaint about the KE4 Max that the finsh doesn't hold...

November 15, 2023 2
Asked a question
TS1-IM bore depth

The bore depth is listed as 1.375-1.250. Is this listed correctly? If so any reas9n for the changes in depth?

July 27, 2023 2
Commented on a post

When an iron doesn't suit a players eye, it can get between his ears. Stepping in with a compact head that seems right can have a lot of good effects. When your swing is on, it works wonders. That compact...

February 15, 2023 2
Commented on a post

The level of feel with the TS3 heads is just incredible. It's an early observation, but the feel just lingers in your head. The type of feel that just leaves you yearning to hit it again.

February 13, 2023 2
Asked a question
TS3 delay?

I had been under the impression the TS3 was all but ready to go.. That the shipment was already stateside. But I'm hearing from Customer service that now it's spring time.  Any clarification on availability?

February 3, 2023 2
Posted an answer
Purchasing experience

I have found the Golfworks web site to be one of the easiest places on the web to make purchases. If he was in a phone.. I don't know if he was but.. by my phone or by computer works flawlessly.

December 28, 2022 5
Posted an answer
Potential KE4 MAX build, thought?

I will echo the comment about the KE4 Max irons being incredible. I play to a 3 and that has been dropping since the KE4 Max irons have been in play. Im a forged iron snob but i Love the KE4s. Its not...

December 12, 2022 5
Asked a question
TS3 in DRM

Is there any hope for a limited run of the DRM finish with the new TS3?

December 3, 2022 2
Commented on a post

The ZT9 shaft is really only a Recoil iron shaft. Low 70g weight, fairly low Tq. Mid high launch. It's characteristics more than likely would be tough to match a driver shaft. For a driver shaft I would...

October 6, 2022 2
Commented on a post

That is an impressive lineup and surprisingly complete of thier offerings. It would be very interesting if you could compile a data acquisition on all of the models. Say do 10 shots with each club and...

October 6, 2022 2
Commented on a post

It was shot in the dark. I'm willing to bet the CPMs of putter shafts are all over the map.

September 19, 2022 2
Asked a question
CPM of a built putter

Have you any numbers on the CPM of a built putter. Or simply the CPM of a putter shaft?

September 18, 2022 2
Answer was selected as best
Puring and FLO questions

When you twang the shaft and the laser had minimal oscillation that is where you orientate the shaft in the 12 o'clock and the 9 is down the target line. Theory is that when hit or swing along that plane...

June 24, 2022 10
Posted an answer
epoxy failure

I've used the Tour set on more than one occasion within 90 minutes. I do so much testing that I'm often crushed for time and will hurry to the range or Simulator. Any failures have been on me by not cleaning...

June 17, 2022 5
Asked a question
Rebirth of the M Series.. Max Milled

If you were a fan of the M Series + be ready to have your socks blown off. The new Max Milled first of is so darn pretty to hold in hand. It's gorgeous. It's easy to see the lineage to the M Series but...

April 4, 2022 2
Posted an answer
Driver Shaft for Higher Swing Speed on a Budget

Take a serious look at the Pro Series by Maltby. A truly inexpensive shaft but can hang with any high dollar brand. They are actually made in the same factory as high end shafts. A shaft that works well...

February 1, 2022 5
Posted an answer
Ts-2 6 iron

I assume in saying a TM4 iron you are referring to a TaylorMade M4? That is a very strongly lofted iron. So if you are using a 6 iron for your 150 shot I really don't think the ability to shape a shot...

January 13, 2022 5
Load More