|
Commented on a post
There are various sources for "special" paint for golf clubs on the internet. I guess it's normal acrylic paint. The only special thing is probably the very fine tip of the bottle. I used one of them. |
April 7, 2023 |
2 |
|
Commented on a post
Nothing special, just normal paint remover. |
March 29, 2023 |
2 |
|
Commented on a post
To get it perfect I spoke with GolfWorks to receive heads at the lower and upper tolerance range. They could do this to a certain extent, but not completely. Then instead of adding or subtracting 1-2 g... |
March 23, 2023 |
2 |
|
Commented on a post
I've only stamped 3 wedges until now. I believe the most important thing is to have a hammer that is heavy enough. A normal household hammer doesn't work. And the support has to be massive and not give... |
March 22, 2023 |
2 |
|
Posted an answer
Why change the ball?Why not make the ball play shorter and use that ball for all players? The pros will lose 20 yards on their 300 yard drive and I'll lose 13 yards on my 200 yard drive. I don't see a problem. If you have... |
March 22, 2023 |
5 |
|
Asked a question
My first set of homebuilt clubsHi everyone, thanks to the forum for support while building my first set of clubs. Attached a few pictures of my version of Maltby clubs. They are all MOI matched but to the 5 hybrid to 2655 kg*cm2. The... |
March 22, 2023 |
2 |
|
Commented on a post
The TS3 has 786 MPF. Brett mentioned that in a post. |
January 30, 2023 |
2 |
|
Commented on a post
Same here. The wedges are ready, the woods are ready, there's a big gap in the middle. |
January 17, 2023 |
2 |
|
Commented on a post
I didn't put any epoxy in the hosel, I didn't want it to build up at the bottom of the hosel. I coated the shaft, stuck it in, twisted it, pulled it out and applied a little more. |
January 17, 2023 |
2 |
|
Asked a question
Gap between shaft and headBuilding my first clubs. Before sanding the tip of the graphite shaft it didn't even fit in the head, after taking the paint off it's a perfect fit. When I roll the shaft in the epoxy, stick it in the... |
January 16, 2023 |
2 |
|
Commented on a post
So my idea wasn't that terrible, only it doesn't work in this case with tapered shafts.... :) |
November 23, 2022 |
2 |
|
Commented on a post
Hi T, thanks for your comment. I'm quite happy with the ball flight, it's at the upper limit of the launch angle. Accuracy is not so great, I was considering if that is a weight issue. My club head speed... |
November 23, 2022 |
2 |
|
Commented on a post
Thanks for the your suggestion! |
November 22, 2022 |
2 |
|
Asked a question
Making irons stifferI was given a set of Mizuno 919 forged irons with Fujikura MCI 60 R shafts. I quite like them but they are a bit soft for me. I was considering cutting the tip by 1/2" and extending the butt. Is that a... |
November 22, 2022 |
2 |
|
Asked a question
mpf of Takomo ironsAre you going to measure the mpf of Takomo irons? Or have you already measured them and I missed it? Thanks, Tom |
August 31, 2022 |
2 |
|
Commented on a post
Thanks for your help! |
August 29, 2022 |
2 |
|
Posted an answer
6-gram tip weightI was just reading about this: "Weight at the shaft tip will move the CG of the clubhead (and thus the "sweet spot" of the club) upward and toward the heel. This is undesirable, but the move is negligible... |
August 25, 2022 |
5 |
|
Commented on a post
Hi Blake, yes, you're right. It's a 5/7 set. :) But you get the idea. I'm playing with less clubs and therefore my gapping needs to be adjusted. The big store would also be happy to sell me single irons. |
August 25, 2022 |
2 |
|
Asked a question
Set-up for half setHi, I'm playing a half set of Mizuno JPX 919 forged with Fujikara MCI 60-R (bought off eBay, not fitted, but I like them a lot). Now I'd like to change, mainly for the fun of changing and also for the... |
August 24, 2022 |
2 |
|
Registered
|
August 24, 2022 |
10 |