Clubmaking Forum

discuss, ask and learn about golf and clubmaking

Commented on a post

Thanks

May 20, 2023 2
Asked a question
Looking at iron shafts for ts4 7i.

I am 73 years old ,currently 12 h with 75+ iron club head speed. My current 7i is TaylorMade m4 with Fujikura Atmos 6r flex. When i make a good swing  ball fight is high trajectory, that I like. I looked...

May 19, 2023 2
Asked a question
Shaft flo laser

When using laser to find the spine of a golf shaft how do you determine between the spine and NBP of the golf shaft.

January 13, 2023 2
Asked a question
Club fitters phoneix az

Can anyone recommend a club fitter in the phoneix area. Wanting to stay away from some of the chain stores

November 24, 2022 2
Asked a question
Fitting for new clubs

Are ther any recommended golf club fitters in the Phoenix area that would be recomend. Not looking for your example PGA superstore,  golf galxey etc.

August 21, 2022 2
Asked a question
Gollf clubs for women

I want to build a golf club for my wife and need some advice as where to begin. She has a consistent swing and 60-70mph club head speed with driver 140-150yds on a average drive. Not over powering as she...

June 25, 2022 2
Asked a question
Beginner clubs for 10 yr old grils and 14 year old boy

What would be a recommendation for golf clubs for a 10 year old gril and 14 year old boy. They are jest starting to hit clubs on my simulator and would like to build a small set to help them learn the...

May 25, 2022 2
Commented on a post

Thanks gives me a lot to think about.

April 12, 2022 2
Asked a question
Graphite shaft cost

What makes a $100.00+ golf shaft better than a $25.00+ golf shaft? For a 12-14 handicap would it make a difference in the higher end of golf shafts. I have started to experiment with building golf clubs...

April 11, 2022 2
Commented on a post

I ended up with the m890 launch tech witch I understand is for woods and not hybrid. I have been in contact with customer service and very helpful. Thanks

April 6, 2022 2
Asked a question
5 hybrid shaft

I purchased the Maltby 5 hybrid and the m890 shaft and came to find the shaft is a .335 and nosel .370. What would be the recommendation for a shaft with .370 tip.

April 5, 2022 2
Commented on a post

Thanks for all the help on recommendations as I am in a learning curve wanting to learn more about club heads,shafts etc.

March 19, 2022 2
Asked a question
Replacement for a 6 iron

I currently have the ts-2 6 iron with the ust iron hl r flex and find that I not being consistent when playing. I am thinking of changing to a hybrid  that would be between my tm burner 5-24* rescue,...

March 18, 2022 2
Commented on a post

My mistake as miss read the chart on ustmamiya web site. Thanks for the correction

March 14, 2022 2
Asked a question
Tip trimming

I have the PROFORCE V2 HL 6F3 that has the tip trimmed 2" and want to use for my 5 wood, trim specs call for 3" end trim for the 5 wood. What could I except with the 2" tip triming?

March 14, 2022 2
Commented on a post

Thanks Rlafoone as it was the pured shaft mentioned pervious. .

February 27, 2022 2
Asked a question
Driver shaft mistake

I have the proforce v2 6f3 hl pured shaft that I install the adapter on for my tm m1 driver. I didn't align it correctly and tried to remove with heat and didn't have and extractor. I applied to much heat...

February 27, 2022 2
Commented on a post

Thanks for the explanation on the differance of the two heads. Is the 2 piece forged head a better head?

February 24, 2022 2
Asked a question
Iron heads

Why is Maltby KE4 Tour + Iron Heads vs TS-2 such a difference in the cost between the 2?

February 23, 2022 2
Asked a question
TM adapter installation on pured shaft

just received my new pured golf shaft with a TM adapter and I am not sure how to align the pure line to the dapter.

February 18, 2022 2
Load More