I did a swingweight calculation at 37.25" for a 7 iron, which would be 1/4" under our standard length, and it comes out in the C9 to D0 range with a standard size 50 gram weight grip. I would recommend...
The Mizuno 925 HMP irons use a .355" tip size iron shaft. The KBS Tour Lite R flex used in the 925 HMP irons is designed to create a high trajectory. The Tour Lite R flex weighs 95 grams. A shaft...
The Alta CB 50 R flex shaft is a shaft made just for Ping and we have never had the shaft and also do not have all the shaft specifications to do an MPF rating. We only do MPF ratings on the shafts that...
The Pro Series+ A flex iron shaft tests a little more flexible through the mid section and stiffer at the tip compared to the Cypher 2.0 A (5.0) flex. They test the same at the butt end. The Pro Series+...
The PTM irons both in Chrome and DBM Black are listed in the MPF ratings in 2018. They rate in the Super Game Improvement Category.
Warming the grip can also help make it a little easier to install.
With the TS3 hybrid/iron Club Pak we use the Pro Series+ Hybrid (MA0403) and the Pro Series+ Iron (MA0404) shafts. The shafts we use in this Club Pak are listed in the Description under Club Pak Includes...
The KE4 Max Forged was made as a replacement for both the KE4 Tour+ and KE4 S irons. The KE4 Max Forged irons have stronger lofts than the KE4 Tour+ irons. The 7 iron in the KE4 Tour+ irons had 33...
At GolfWorks we use to sell and use the Club Conex system, https://www.clubconex.com/ It was sold and the company chose to bring it back all in house. Not sure if you have checked with them yet.
We are able to adjust the DBM finish irons and wedges up to 2 degrees for both loft and lie. The feel for adjusting is similar to the chrome finish heads.
The BBGM on the DRT wedges measures 1.5".
The Core Blue TS FW tests stiffer at the butt, tip and through the mid section compared to the FW S flex. The stiffness profiles are similar with the TS testing about three quarters of a flex stiffer...
Bore Depth and Insertion Depth are the same thing and it does measure 1.355" on the TS3 irons. When I measure the bottom of bore to ground line measurement on the TS3 irons it measure at 3/4". There...
I would recommend calling our Pro Shop. Fittings are done by appointment and you will need to schedule an appointment. The guys can also tell you what they can or cannot do in terms of the Jumbo Max...
The Aerotech SteelFiber shafts are graphite shafts. They are graphite shafts with a very, very, very fine steel fiber spiral wrapped through the shaft. They dampen vibration very well. The Aerotech...
I initially measured the 7 irons of the TS3 and TS4 irons and both of them measured with a 3/4" BBGM. I just measured them again and I am still getting 3/4". I also just measured a full set of TS3...
I just happen to have a RAC 6 iron head sitting here in my office and when I check the head weight it is 257 grams. Our spec head weight on the STi2 Gen 2 6 iron is 260 gram with a +/-3 gram tolerance. ...
We do not list the CG measurements on the wedges but they would also be pretty similar with the TSW, Max Milled and DRT wedges. Wedges tend to have slightly higher CG's because of their increased loft. ...
I am told we are working on a new RH driver for 2026 and we may also add a LH version of the same driver. The decision on the LH model has not been made for sure yet. It is still very much in the model...